Dataman 48UXP Instrukcja Użytkownika

Dataman-48UXP Intelligent Universal Pr

1 General Information CHAPTER

Introduction The Dataman-48UXP is a high performance intelligent PC-based universal programmer that works through your

Device-insertion and continuity checks – No mistakes! The Dataman-48UXP performs device-insertion and continuity checks before programming each devi

Using the Dataman-48UXP Software Menus Accessing the menus can be done in two ways: 1. Use the mouse and click on the menu option displaye

2 Installation CHAPTER

Minimum PC System Requirements Win 95/98/ME, Win 2000, Windows XP, Win NT 4.0 or latest (NT OS system, need NT System ADM). CUP: PII 750 a

installation program. 3. Following successful installation, run the software by executing Dataman-48UXP by double click the Dataman-48UXP ICON. The

3 Command Hierarchy CHAPTER

Dataman-48UXP Command Hierarchy System command Operation command Hot Key File (ALT-F) Save Buffer ALT-S Load File ALT-L Exi

4 Operation CHAPTER

Copyright Notice This document is copyrighted, 2000, 2001, 2002 by DATAMAN PROGRAMMERS LTD. All rights are reserved. DATAMAN PROGRAMMERS LTD. reserv

LED Display The Dataman-48UXP has a three LED display to indicate the status of the socket. Read this section carefu

File name Specify the destination and file name which you want to save to. File format Select the file format of your output file, click the right

This writes the bytes 3,7,11,15, ... into the output file. 4th byte of 4 This writes the bytes 4,8,12,16, … into the output file. From Buffe

File name This specifies the file name and its destination Auto Format Detected The software automatically detects the format of the file that

To Buffer Address Starting address of the buffer to load the file into, if the data read is to be copy into a specific area of the buffer, fill in

Exit Menu File / Exit Hot key Alt-X Quit the Dataman-48UXP program

Project File Commands Save Project Menu Project / Save Project Hot key Alt-F1 This option saves the current setu

How to use this manual Thank you for purchasing the Dataman-48UXP intelligent universal Programmer. We designed this manual

This option is used to select a new device as the active device. It is important to select the correct device, as the algorithms used to program dev

party adapter. Other useful example in device, package and adapter. 1) For example a 1M bit flash (29F010), this chip has three kind of packages, 32

Keyboard Press TAB until the cursor is flashing in the “Type” box. Use the up and down arrows to go to the appropriate type. Press the space bar to

such a function since the A9 location do not standardize for chip over 40 pin, using such a function may damage the chip since a 12V high voltage wi

menu and the contents is different from chip to chip), reference to device configuration section. The last set up menu is statistic configuration se

Figure 4.2 mass production mode screen Editing the Buffer (memory device ) Menu Device / Edit Hot key Alt-E This function is used to e

Radix This button controls the display of the memory address in Hex/Decimal format. If the address is currently displayed in decimal format, clicki

Original file 01 23 45 67 89 AB CD EF after swap with word width 2. 23 01 67 45 AB 89 EF CD Original file 01 23 45 67 89 AB CD EF

search string can be text code or hex code, it can search forward from cursor position or backward from cursor position. Next This commend is to fi

In the mode, “X” refers to blown fuse, and “-“ refers to an intact fuse. The purpose of the buttons is as follows: Radix This button control the d

Packing List Before you begin installing your Dataman-48UXP, please make sure that the following materials have been

devices, the option is used to modify the vectors that will be used to test a device after the logical chip has been program, this test vector is us

Insert You can insert a line of vectors by clicking this button. The position where the line will be inserted depends on the position of the cursor.

N Power pin and the outputs not test X Output not tested, input default level Z Test input/output with high impedance

Figure 4-4 Programming progress screen Verifying a Device Menu Device / Verify Hot key Alt- V This function compares the contents of the

Figure 4-5 Device verification screen Memory Protect/program configuration Menu Device / Memory Protect Hot key ALT-U (PLD only) This

will automatically program the main memory and program the configuration byte in a single command (program or mass production mode program). Special

Fourth Select the error display format. Important notice in function test To perform function test after program the PLD chip, the input file mu

commend is to compare the buffer data with the device data, when the first data difference founded, the software will stop and report the buffer add

Options Modify Programming Parameters Menu Options / parameters modify Hot key F3 This function allo

Figure 4-8 Example screen: Device-specific operation options The following options can be set: Start address, End address This is the start an

Contents Chapter 0 Quick Start ... 0-1 Quick Start...

buffer size is 80 (Hex), will therefore an end address of 3F. When selecting a start or an end-address, you should align the buffer on the right b

ASCII Decimal Hex format example 0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17, … Modulo-26 format example A,B,C,D,E,F, … ,Z,AA,AB,AC, …. Insertion

(．) Twice Vcc ±5% When this option is selected, the Dataman-48UXP will do two verify passes on the device: one using Vcc+5%, the other Vcc-5%. Exam

set up menu do not set the lock bit or protect bit enable. Auto-Erase/Overwrite Option This option only applies to chip, which is electronically e

Statistic Menu Options / Statistics Hot key F6 Action Enable the counter or alarm when target count or maximum failure counter r

Count how many verify operations into the display. Blank check enable: Count how many blank check activities into the statistic display Erase enabl

Manufacture recommend the user can run self-test of Dataman-48UXP prior to each day’s operation. The self-test routine including testing the parall

Dataman-48UXP programmer need to return to your distributor for repair. The DAC (four DAC in Dataman-48UXP) test result and its meaning DAC0 25 34

5 Using Adapters CHAPTER

Adapter Requirements Dataman-48UXP supports universal 48-pin TSOP, 44-pin PLCC, 44 pin QFP, 44 pin TQFP, 44 pin SOP, 40-pin TS

Programming a Device... 33 Verifying a Device... 34 M

SDP-UNIV-16SO/170 16 pin SOIC (173 mil) universal adapter 1.27m pitch SDP-UNIV-20SO/200 20 pin SOIC (207mil) universal adapter for 8-20 pin SOIC

SDP-UNIV-40TS/W 40 pin TSOP (10mm x 14mm) universal adapter for 40 pin TSOP Flash memory SDP-UNIV-40TSS 40 pin TSSOP universal adapter for 40 pin

SDP-7096-100Q 100 pin QFP adapter for ALTERA 7096 SDP-7128-100Q 100 pin QFP adapter for ALTERA 7128/E SDP-7160-100Q 100 pin QFP adapter for ALTER

SDP-C923-68 68 pin PLCC adapter for Microchip PIC 16C923/924 SDP-11K1-84 84 pin PLCC adapter for Motorola XC68HC11K1/K4 SDP-96MH-84 84 pin PLCC a

LVT-640W18-56U uBGA adapter for Intel 28F320/640/128W18 (1.8Vcc, I/O) LVT-640W30-56U uBGA adapter for Intel 28F320/640

SDP-A320-63F 63 pin uBGA adapter for AMD29DL32X (8x14mm size) SDP-41DL16-69F 69 ball FBGA adapter for AMD 41DL16xxMCP SDP-42DL32-73F 73 ball FBGA

A Error Messages APPENDI

Error Messages Cold not open file – nnnn! This file does not exist. You might have typed the wrong filename or you might

Device inserted backwards or damaged already! The Dataman-48UXP detected that the device has been inserted the wrong way round, or that the device

Dataman-48UXP not found! The Dataman-48UXP software does not detect the Dataman-48UXP on of the parallel ports, or the Dataman-48UXP may be failure

0 Quick Start This section is for experience user only, after install the Dataman-48UXP hardware and successfully install the system software in you

have selected an incorrect device as active device, or the device is an older/newer version than the device supported by the Dataman-48UXP. Select

Poor contact at pin %s! The Dataman-48UXP does an insertion test before programming/erasing etc. any device. This message indicates that the socket

adapters. The system is in demo mode! The Dataman-48UXP was not found when the software was started up, and went into “Demo mode”. You can still ru

Quick Start After execution the Dataman-48UXP software, following Dataman-48UXP screen will display: It shows the fi

Read operation (Hot Key ALT-R), you can transfer the chip′s contents into the buffer. 4) Insert blank chip of the same type into the ZIF sock